RTV2 Moldmaking Platinum Cured Liquid Silicone Rubber, produced by Dongguan Gangtian Polymer Material Co. Ltd, stands out as an exceptional addition cured silicone rubber for mold making. This versatile two-component liquid silicone rubber vulcanizes at room temperature, providing a Translucent finish.

Designed for various applications, such as mold making for foods (candy, cake, cookie, chocolate, ice cube, fondant, etc.), jewelry, tires, rapid prototyping, life casting, realistic masks, epoxy resin products, candles, vacuum foaming, prosthetics, and more, it exhibits Food Grade and Medical Grade standards.

Applications
In addition Cured Silicone Rubber has extensive use, such as mold making of foods (candy, cake, cookie, chocolate, ice cube, fondant etc), jewelry, tires, rapid prototyping, life casting, realistic mask, epoxy resin products, candle, vacuum foaming, making of prosthetic breast, artificial skin, human body, adult toys, baby feeding nipples, phone case and so on.

Techinical Parameters
Model Code GTSIL-P10 GTSIL-P15 GTSIL-P20 GTSIL-P25 GTSIL-P30 GTSIL-P35 GTSIL-P40
Hardness - Shore A 8-10 14-16 19-21 24-26 28-30 34-36 38-42
Viscosity - Cps 3000-5000 4000-6000 4000-7000 5000-8000 6000-9000 6000-10000 4000-6000
Mixing Ratio - % 1:1 1:1 1:1 1:1 1:1 1:1 1:1
Tear Strength - KN/m2 14-17 16-18 18-22 22-26 20-23 16-19 12-16
Tensile Strength - Mpa 3.5-5.5 4-6 4-6 4-6 4-6 4-6 3.5-5.5
Shrinkage - % 0.10% 0.10% 0.10% 0.10% 0.10% 0.10% 0.10%
Elongation - % 500-600% 500-600% 500-600% 400-500% 400-500% 350-500% 300-450%

How to use
1. Substrate Preparation
The surface of the original should be clean and free of loose material. If necessary, and in particular with porous substrates, use a suitable release agent such as petroleum jelly or soap solution.

2. Mixing
Thoroughly stir Part A (silicone base) before use as filler separation may occur upon prolonged storage.
Weigh 100 grams Part A (silicone base) and 3 grams Part B (curing agent) in a clean container. Mix together until the curing agent is completely dispersed in the base. Hand or mechanical mixing can be used, but do not mix for an extended period of time or allow the temperature to exceed 35°C (95°F). Mix suitably small quantities to ensure thorough mixing of the par A (silicone base) and part B (curing agent).

It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mix to completely expand and then collapse. After a further 1-2 minutes under vacuum, the mix should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture, so a suitably large container should be chosen.

Caution: prolonged vacuum will remove volatile components from the mix and may result in poor thick section cure and non-typical properties.

Note: If no vacuum de-airing equipment is available, air entrapment can be minimized by mixing a small quantity of par A (silicone base) and part B (curing agent), then using a brush, painting the original with a 1-2mm layer. Leave at room temperature until the surface is bubble free and the layer has begun to cure. Mix a further quantity of base and curing agent and proceed as follows to produce a final mold.

3. Pouring the Mixture and Curing
Pour the mixed Par A (silicone base) and Part B (curing agent) as soon as possible onto the original, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 24 hours at room temperature (22°C-24°C/ 71.6°F - 75.2°F) and the mold can then be separated from the original. If the working temperature is significantly lower, the cure time will be longer. If the room temperature or humidity is very high, the working time of the catalyzed mixture will be reduced. The final mechanical properties of the mold will be reached within 7 days.

ADDITIONAL INFORMATION
Reproduction of Vertical Surfaces

If a skin mold is required of a vertical object or surface and cannot be made by normal pouring techniques, the catalyzed mixture can be made non flowable by the addition of thixotropic agent.

1. Prepare the original as described earlier.

2. Brush the original with a thin layer of catalyzed mixture. Repeat the operation when the first layer has started to cure, to achieve a coating thickness of >2mm. Leave to cure at room temperature until the material is tacky.

3. Prepare a new catalyzed mixture of silicone and add 1% by weight of thixotropic additive and mix thoroughly until a paste consistency is reached. De-airing of the mixture is not required.

4. Using a spatula, cover the coated original with the thixotropic coating until all undercuts are filled; leave to cure for 24 hours at room temperature.

5. Construct a support mold using polyester resin or plaster and allow to set in contact with the silicone coating. Carefully remove the support mold. Peel the rubber off the original and place in the support mold.

Use at High Temperatures
Some molds produced from condensation cure silicone rubbers can degrade when exposed to temperatures above 150°C (302°F) over a period of time or when totally confined in storage at high ambient temperatures. This can result in softening and loss of elastic properties.

Resistance to Casting Materials
The chemical resistance of fully cured silicone rubber is excellent, and similar to all condensation cure silicone elastomers. It should be noted however that ultimately, resins and other aggressive casting materials will attack silicone molds, changing physical properties, surface release and possibly mold dimensions. Molds should be checked periodically during long production runs.

Shelf life
Twelve (12) months from date of shipment when stored at 25ºC in the original sealed packages.

Package
Silicone Packed in clean 25kg/pail, 200kg/drum.
Catalyst packed in 1kg/bottle.

Health and safety
Catalyst contains toxic element. Avoid contact with eyes. Flush eyes with water and seek medical attention. Remove from skin with waterless hand cleaner followed by soap and water. Children should not use this product without adult supervision.

GTSIL-T Series silicone is an industrial product and must not be used in food molding, dental and human skin molding applications.

Our Advantages
We can be your reliable one-stop supplier of liquid silicone rubber, we focus on a wide range of silicone rubber such as HCR, LSR, RTV-2, HTV and other silicone products like electrical silicone potting, silicone gel, silicone oil, silicone gum, etc.

We can be a strong backing for you to provide materials, our silicon rubber yield is 500 tons/month at least.

We promise that the quality of our silicone rubber is as good as we describe, only use Dow sil, Wacker, Shin-Etsu, BlueStar and other well-known brands as our source of raw materials.

We can provide silicone rubber at a more competitive pricing, which can make you to earn more profits.

We have our silicone rubber certificates approved, such as FDA, MSDS, REACH, RoHS, etc.

We have our professional freight forwarders, they will surely free you from troublesome shipping stuffs.

We support to do transaction with you on Alibaba,a large-scale official international trade platform in where

The rights of suppliers and buyers can be guaranteed safe.

We can provide you with free sample for testing, which can relieve your worries before you volume order.

We support to do any custom service for you,no matter the parameter of silicone rubber, colour, logo and even packages.